ASIC REPAIR WHATSMINER PRO TESTER fixture M20 M20S M21S M30 M31 M50 all others

TESTER FOR DIAGNOSTICS AND REPAIR OF WHATSMINER ASIC REPAIR

• Diagnostics hashboard models:
• M30, M30K, M30L, M30S++, M30S+, M30S, M31, M31H, M31L, M31S+, M31S, M31SE, M32, M33, M34S+, M36S, M39, M50, M11, M12, M1S, M20, M20S+, M20S, M21, M21S+, M21S, M29
• Helps determine faulty chip on the hashboard.
• Flashes EEPROM without removing the device from the shelf.
• EEPROM editing, hashboard model auto-detection, the ability to record your serial number.
• Saves your money and time.

 

·         SAVING EEPROM FROM THE BOARD TO A FILE

Sometimes you need to save EEPROM to your computer in order to be able to restore it or share it with colleagues, this can be done easily and quickly in the Web interface.

The saved file will be in the bin format and can be later written to the boards by both the tester and any other programming device.

·         WRITING A DUMP FROM A FILE TO A BOARD

You can write the previously saved file to the board from the Web interface.

The file must be in bin format, it can be read by both the tester and the regular programmer.

·         READING AND WRITING EEPROM WITHOUT WEB INTERFACE.

You can read EEPROM from the working board and immediately write it to other boards, you only need to connect the tester to board!

·         EEPROM EDITOR

The tester allows you to change the hashboard parameters.

You can assign your serial numbers to boards for further accounting.

All contents of the EEPROM are on the board stickers, the tester makes it possible to restore a damaged EEPROM by entering data from the hashboard stickers.

 

 

 

·         CHIP MAP

Accurate map of the location of chips on the board.

Hashboard map repeats the location of the chips on the board, which saves time searching for a chip in each iteration. You only have to find the highlighted chip and start measuring!

You do not need to remember the location of the chips or refer to the diagram. The map will show you where the chip you need is located!

If you change 50 chips per day, then this function will save you up to one hour, which means you can repair more boards!

·         BOARD MODEL AUTODETECTION

Automatic model detection of the board upon connection.

Checking the integrity of the EEPROM firmware.

Display of the board parameters written to the EEPROM firmware, with the ability to edit.

·         TESTING THE RESET LINE

Power on the board, press RESET button, the tester will check if the reset signal comes from the first to the last chip and report the result, and you can take measurements on the board and find the faulty chip.

An active button changes the state of the reset line to a logical one, an inactive button to a logical zero.

 

·         CHIP TESTING WITH RESET

At the beginning of testing, the tester checks the state of the reset line from the first to the last chip and reports the result..

If you select the test with reset option, the reset will occur before each iteration of the polling of the chips and display the counter of successful and unsuccessful resets in the test log.

 

·         LOG OF FAULTY CHIPS

The web interface displays the fault history of all chips during one test:

• Displays information about the connected board;
• Shows which chip is currently faulty;
• Shows information about the number of failures in the chip itself;
• The log stores the entire history of testing operations, including what chips were faulty;
• At the end of the test, you will receive a summary of the faulty chips;

This function will not allow you to miss a fault, will do repairs more convenient, clear and reliable.

 

·         POLLING MODE FOR SELECTED CHIPS

Sometimes an engineer needs to interrogate one or more specific chips to study their responses

To do this, we created a polling mode for selected chips

Just click on any chip in the web interface during test and take measurements!

 

·         BOARD TESTING - UNADDRESSED POLLING OF CHIPS

Unaddressed - broadcast chip polling, returns only the number of responding chips.

 

·         ADVANCED BOARD TESTING - TARGETED CHIP POLLING

Adressed chip polling, returns the response of each responding chip.

This mode is completely identical to the standard Whatsminer test.

Also, only in this mode, the chips report their chip ID..

 

·         MOBILITY AND FREEDOM

Asic Repair Center powered by standard USB type-c, this means that you can power it from any adapter, laptop or even power bank! You don't need another power adapter, you need mobility and freedom and we gave it to you!

 

·         EASY UPDATE

In the web interface, you can see the current firmware version and available updates that are installed with the click of a button.

You do not need to download anything, you do not need to deal with update technologies, no need to think about how to test just released to the market model, you just need to click the "update" button, the rest will be done by us and Asic Repair Center!